Communicate with Supplier? Supplier
Alan.pang Mr. Alan.pang
What can I do for you?
Chat Now Contact Supplier
 Tel:86-662-6667958 Email:alan.pang@superwins.com.cn
Video Dispaly
  • iMX Series Exchangeable Head Milling System

    2019-07-15

    iMX series Exchangeable Screw on Head Series End mill brochure is available for download at:…iMX series Exchangeable Screw on Head connection features the Worlds first* “Carbide Head”+”Carbide Holder” double face contact connection but, we did not stop there. Careful SWOT analysis of the conventional screw on head products indicated it was PARAMOUNT to re-engineer the carbide head joint connection for the next generation of Exchangeable head products to approach the performance of solid carbide end mills without encountering carbide joint failure due to tensile strength limitations of carbide threads. Therefore, to overcome inherent tensile strength weakness of carbide threads, Mitsubishi Materials Engineers developed a process that enables a SPECIAL STEEL screw joint to be securely incorporated into the BOTH the CARBIDE HEAD and SHANK thus avoiding thread tensile failure common with ground carbide threads. The result for you is a highly reliable connection that can cope with high cutting loads and coolant thru head options.In fact, the iMX connection was specifically designed to excel in high demanding heat resistant Aerospace applications were failure mode is typically attributed to joint rigidity resulting in run-out, deflection and poor tool life. The Economical iMX Series Exchangeable Screw on Head Ends are available in Coolant through and non-coolant configurations and will soon be your default solution to costly solid carbide end mill applications. *According to our own research on exchangeable head end millsMitsubishi Materials brochures are available for download. Just select appropriate link below: Industry Specific brochures are available for download at//…Grade product brochures are available for download at//… Turning insert product brochures are available for download at//… External Turning Tool product brochures are available for download at … Boring Bar product brochures are available for download at//… Grooving Tools product brochures are available for download at//… Solid Carbide End Mill product brochures are available for download at … Milling product brochures are available for download at//… Drilling product brochures are available for download at//…To see all Mitsubishi Cutting Tool product channels on YouTube, follow link: … Or, visit one of our product specific channels below: The Cutting Edge: … Medical Dental Channel: … Turning & Boring Channel:… Milling Channel: … Drilling Channel: … Grooving Channel: … Swiss Tooling Channel: … CBN Channel: … Solid Carbide End Mill Channel:…Mitsubishi Materials USA – Cutting Tools, Social Media Sites: Face book: … Twitter: YouTube: …Additional Resources: Experience Mitsubishi Carbide’s Patented Online Catalog with downloadable CAD files … More Mitsubishi Cutting Tool Videos can be found at//…Questions please contact: Technical Support at 1-800-486-2341 Or Email Secure technical inquiries can be submitted to Mitsubishi Materials at … Thank you for taking the time to view this video and please visit Mitsubishi Materials USA at

  • Hurco VMX42SRTi cutting fast 5 axis component

    2019-07-15

    Subscribe to our channel – have another Channel specifically for engineering company videos – view and subscribe here are proud to offer a platform that educates engineers throughout the World. Our main audience is the UK market and you’ll see from this video that we focus on learning and talking to UK based engineers. We do travel to Europe and review products on request of our clients. See Videos on MTDCNC here ’s not just videos that MTDCNC offers to our users, we promote used machine tools for sale, new machine tools for sale, ex demo machines and also related equipment, such as cutting tools, including end mills, drills, countersinking tools, shell mills, radius tools, boring tools, reamers and much more for both milling and turning. Beyond the cutting tools we also offer the accessory solutions, these include the Workholding, vices, 4th axis units, collet chucks, 3 jaw chucks, bar feeds and toolholders. Toolholders is an interesting one as this could be one of many differing toolholders such at BT40 tooling, BT30, HSK 63 and then for turning VDI 30/VDI 40 toolholders.Find new and used machine tools for sale here Find cutting tools for sale here Find workholding, vices and more here Find automation for machine tools here Find CAD CAM software here website also has a great news feed, we deliver news to the UK market every hour relating to manufacturing, machine tools, cnc equipment and events.For the latest news click here For machine tool and tooling user stories out our event videos, they really are unique. In all our youtube channel and our website are great for engineers and machinists.You can also follow us on twitter here And on Facebook here: Our LinkedIn Page: DON’T FORGET TO SUBSCRIBE TO THIS YOUTUBE CHANNEL TO GET MORE OF OUR GREAT ENGINEERING VIDEOS!

  • ☃ Buy Now Stainless Steel Manual Lemon Juicer Fruit Juice Ex Cashback

    2019-07-15

    Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Too Recommended : Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools SqueezersYour like Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Product details of Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Cheap to you.Category Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Cheap Compact and sleek design,Easy to use and clean.This Stainless Steel Lemon Squeezer Juicer is a best tool tofully extract juice from lemon and orange.This manual lemon squeezer enables you to enjoy lemon/limejuice right away.Produce delicious fresh juice for your bar or yourrecipes.These squeezer are rustic, unpainted, simple and easy touse.more Home Appliances Small Kitchen Appliances Juicers Fruit Comparison.Prices Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Best.Do not wait to do your lucky to come Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers.Lets take a little Reply Check out ✓ Thailand Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Is a quality product at a yet unknown. The prevalence Where there is a never before price was reasonable affordable Say that it is the cheapest delivery I worry Overtook Jaime wait a few days to reach its home page do not worry, we will not deliver the goods. Our restaurant is open for Reliable ★ Special buy You are lucky to find Because Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers Of high quality and very good value. We have shipped to you quickly. I guarantee that you will not be disappointed with the product.———————————————————————————- Search : Stainless, Steel, Manual, Lemon, Juicer, Fruit, Juice, Extractors, Kitchen, Tools, Squeezers, Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools SqueezersStainless #Steel #Manual #Lemon #Juicer #Fruit #Juice #Extractors #Kitchen #Tools #Squeezers #Stainless Steel Manual Lemon Juicer Fruit Juice Extractors Kitchen Tools Squeezers

  • How to assemble the ingolf ikea bar stool chair

    2019-07-15

    Instructions on how to assemble and build the ingolf ikea bar stool chair and tools needed.

  • Estwing Hammer Chisel (More Than Just Friends With Browning Tomahawk)

    2019-07-15

    SHOP FOR ESTWING TOOLS USING THE LINKS BELOW, MADE IN THE USA!: Estwing Sportsman's Axe/Hatchet: Estwing 16 Inch Camp Axe: Estwing 26 Inch Camp Axe: Estwing Carpenter's Hatchet: Estwing Rigger's Axe: Estwing Double-Bit Axe: Estwing Tomahawk: Estwing 3LB Engineering Hammer: Estwing Wood Splitter/4 Pound Hammer: Estwing Rock Pick/Mason's Hammer: Estwing Long Rock Pick/Warhammer: Estwing 18 Inch Pry Bar: Estwing Roofing Pry Bar/Nail Remover: Estwing Sport Machete: OTHER TOOLS: Pulverizer Demolition Hammer: Truckers Friend: Klenk Insulation Knife, Wood Handle: Klenk Insulation Knife, Synthetic Handle: The Estwing Geologist Rock Hammer/Chisel is 10.4 inches in length, 12 ounces in weight, and made of 1055 steel. Price is around $30. I like this hammer/chisel because it is solid but portable. It makes a great companion to the Browning Shock n Awe Tomahawk, as these two together give you the blade, pick, hammer, and chisel. It can be used for many things including fixing things around the house, building shelters, or as a small urban survival escape/rescue/entry tool. The chisel part is also good for prying and digging. The chisel does not have an edge because it is meant for rocks, but you can sharpen it if you want to use it to shape wood and pry.

  • DIY: Ford Ranger 2wd Upper Control Arm Replacement

    2019-07-15

    Right control arm (Canada): Left control arm (Canada): Right control arm (USA): Left control arm (USA): US website: Canadian website: Video tutorial on how to replace the upper control arms on a Ford Ranger. The truck I’m working with here today is a 1998 Ranger 2wd equipped with front coil spring suspension. The same procedure can also be applied to the Mazda B series trucks. The upper control arms on this truck has an alignment adjustment that affects the camber. I would highly recommend having your taken in for an alignment. If the alignment is incorrect, this can affect the handling and also cause excessive wear on your tires. The control arms can fail in a couple ways, one is through the ball joint and the other is through the bushings. When worn you may notice clunking, irregular handling, or uneven wear on your tires. In an extreme situation, the steering knuckle can separate from the upper control arm at the ball joint. Website: Patreon: Facebook: Google Plus: Twitter: Instagram: Tumblr: Pintrest: Tools/Supplies Needed: -15mm socket -16mm socket -3/8” drive ratchet -1/2” drive ratchet -1/2” breaker bar -wire brush -new control arms -spray paint or a paint marker -hammer -sandpaper -jack and stands -punch Procedure: -safety elevate the front of the truck, use jack stands, and then remove the wheels -remove the rubber barrier which is held on with plastic clips -use a wire brush to clean up the threads and camber adjustment plates -mark the camber plates using a paint marker or spray paint -remove the 15mm pinch bolt which connects to the steering knuckle -using a hammer, knock out the pinch bolt and then tap the control arm out of it’s location -to remove the control arm bushing bolts, they require a 21mm socket and remove the bolts -do not mix up the camber plates as they are different between each side -pull out the control arm -compare the old and new control arms to ensure they are the same -there are different control arms for both the right and left sides of the truck -using sandpaper, clean up the pinch clamp where the ball joint fits into place to remove any debris -reinstall the new control arms, snug the arms in place but do not tighten them -install the ball joint in the pinch connection and then install the pinch bolt -you may need a hammer to help assist that bolt into place, be careful not to damage the threads -the torque spec for this bolt is 35 to 46 ft lbs -the same procedure applied to the opposite side -using a wire brush, clean up the threads of the bolts and alignment areas so it can be easily marked -remove the rubber barrier which is held into place with the plastic clips -I used paint to mark the outline of the eccentrics, a paint marker can also be used to make lines instead -using a 15mm socket and wrench, remove the pinch bolt -then knock out the pinch bolt with a hammer -use 21mm sockets to remove the control arm bushing bolts -in order to break these bolts free, I used a breaker bar first -remove the control arm -clean up the spot where the ball joint fastens into the steering knuckle using sandpaper -install the new control arm, you may need a hammer to gently tap it into place -install the bushing bolts and snug everything into place, but don’t fully tighten them just yet -install the ball joint into the steering knuckle -install the pinch bolt and then tighten, the torque spec for this bolt is 35 to 46 ft lbs -reinstall the wheels on both sides, the vehicle should be on responsibly level ground to do the bushing preload -tighten the control arm bushings, the torque specs for these bolts are 83 to 113 ft lbs Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week! © 4DIYers 2013 All Rights Reserved No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

  • Swarf and Chips Aug 18th – Are these the best milling machines in the World?

    2019-07-15

    00:27 – DTS UK Overview 01:01 – We discuss brands -Johnford - Honor Seiki - Pro Design - Correa 12:50 – We travel to Correa in Spain 19:24 – Special Offers 20:43 – Andy Bailey talks serviceThis week’s show is a DTS UK takeover show. Paul and Lyndsey are joined by Ian Horton and Andy Bailey from DTS. During the show Ian discusses the Johnford heavy duty milling machines, the Honor VTL range, their new Pro-Design 5 axis machines and puts a big focus on Correa. Also on the show we tour Correa’s manufacturing facility in Spain and conclude activities talking to Andy about DTS UK’s service and support. Subscribe to our channel – have another Channel specifically for engineering company videos – view and subscribe here are proud to offer a platform that educates engineers throughout the World. Our main audience is the UK market and you’ll see from this video that we focus on learning and talking to UK based engineers. We do travel to Europe and review products on request of our clients. See Videos on MTDCNC here ’s not just videos that MTDCNC offers to our users, we promote used machine tools for sale, new machine tools for sale, ex demo machines and also related equipment, such as cutting tools, including end mills, drills, countersinking tools, shell mills, radius tools, boring tools, reamers and much more for both milling and turning. Beyond the cutting tools we also offer the accessory solutions, these include the Workholding, vices, 4th axis units, collet chucks, 3 jaw chucks, bar feeds and toolholders. Toolholders is an interesting one as this could be one of many differing toolholders such at BT40 tooling, BT30, HSK 63 and then for turning VDI 30/VDI 40 toolholders.Find new and used machine tools for sale here Find cutting tools for sale here Find workholding, vices and more here Find automation for machine tools here Find CAD CAM software here website also has a great news feed, we deliver news to the UK market every hour relating to manufacturing, machine tools, cnc equipment and events.For the latest news click here For machine tool and tooling user stories out our event videos, they really are unique. In all our youtube channel and our website are great for engineers and machinists.You can also follow us on twitter here And on Facebook here: Our LinkedIn discussion group: DON’T FORGET TO SUBSCRIBE TO THIS YOUTUBE CHANNEL TO GET MORE OF OUR GREAT ENGINEERING VIDEOS!

  • Aluminum 6-blade impeller (CNC 5-axis project)

    2019-07-15

    Student project for an impeller workpiece. Students used CAM software to direct the simultaneous 5-axis motion. The finished impeller highlights many machining techniques; some decorative features include the compound-angle tapped holes and the ported central spline shape. Mill tools used: 3/8" roughing ball endmill, 3/8" tapered 7º endmill for finishing, 1/16" ball endmill for engraving. The drilling module used a 1/2" spotdrill, .159" drill, and 10-32 taper tap (not shown) Lathe tools used (not shown): 55º DNMG432, 27/64"dia drill with 1/2-13 tap, 3/8" carbide boring bar with 55º D-style insert. The workpiece is bolted onto the trunnion platter using a 1/2-13 screw from the backside.

  • Replacing camera LCD: Fujifilm

    2019-07-15

    First of all, I think most of the fujijfilm “F” series similar to repair. This one is specifically for the “Fujifilm Finepix F200EXR”I started off with the unboxing of an LCD screen I ordered from eBay. I saw a couple of repair videos that talked about getting the LCD and tools but I was out of luck. I was suppose to get a screwdriver with three slits. I figure that the type of screw on the camera is a security screw. Instead, I got a normal 4-slitted screw driver. The box also came with a tool to peel the shell off the camera. It was much too flimsy and weak to be of use. I broke it the first try. I had use my hand which worked just fine. And of course the LCD screen. I did not have a good start with the repair. The provided screw driver was too big for 80% of the screws I needed to take off. I had to resort to a 1.4 mm flathead screw driver. This is usually the smallest driver available in a precision tool kit. I took off all the outside screws I can see except for the security screws. I then took off the inner screws attached to the shell and the camera. As a side note, remember which screw goes where. I had some trouble putting everything back together because I mixed my screws around. The case just did not fit snugly and I had to start over again. Anyway, I peeled off the shell from the security screws. I knew that this would break the shell. Inside the camera, I took off a vertical bar that the camera control buttons were lying on top of. The bar was in the way of the LCD wire. At first I did not know how to unhook the original LCD. I just got frustrated enough that I pulled the wire out. It worked. The hard part was putting the wire back in. I struggled for a while trying not to damage the LCD’s wiring but again, my frustration got the best of me. I just shoved the wire in and turned the camera on. At first try, the LCD not turn on. I pulled it out and then did not care anymore if it broke. I shoved it back in using my finger nail and bending the cable 180 degrees. I made sure that wire was pushed all the way in and turned the camera on. It worked. I started to put everything back together again. The vertical bar, the shell, and the sides of the shell. Make sure at you put the screw in the same order that they were in. Also make sure that you have clean working area as to not loose a screw if you fumble and drop it.

  • Buy STRUCTURES by Malouf Heavy Duty 7-Leg LINENSPA Adjustable Metal Bed Frame with Center Support a

    2019-07-15

    Easily Adjusts to Fit Queen, Full, Full XL, Twin XL and Twin MattressesSeven-Leg with five 3″ Heavy-Duty Metal Reinforced Glides1-1/2″ Center Support Bar with Support GlideUniversal Headboard Brackets and Gunmetal Black Matte Powder CoatingEasy Assembly in Under 10 Minutes – No Additional Tools RequiredSupport your mattress with a heavy duty steel bed frames engineered to support today’s thicker, heavier mattresses. A 1-1/2″ center support bar offers extra support through the middle of the bed and fulfills mattress manufacturers’ support warranty requirements. Seven-leg with five heavy-duty 3″ metal reinforced glides allow mobitily when desired. Headboard brackets will accomodate virtually any headboard configuration. Two cross arm support legs con

  • Professional Mixology Bar Set For Less Than $100

    2019-07-15

    ADD ME INSTAGRAM @slickbartender_ Watch How to Build Mixology Bar Set that you can use to make handcrafted cocktails All links can be found in the description in the video about Chinese tools here: Bar Set for Bartenders video here: Mixology Bar Tool Bag here: #MixologyBarSet #MixologyTools Contact: Mail: 2283 Bridlewood Drive 89119 Las Vegas NV

  • How To Build A Custom Bar Set For Bartenders (Bar Tool Roll)

    2019-07-15

    ADD ME INSTAGRAM @slickbartender_ Contact: A lot of you asked me to give recommendations about bar tools. So in this video I explained that you should have a bar tools set for work behind the bar, for events and nice to have during interview/audition when you trying to get a bartending job! THis is still pretty affordable set and after ALL customizations total cost shouldn't be more than $150 IMPORTANT: If you prefer instead of buying set with tools and replacing some, you can just get empty bag and fill up with tools that are best for you. Here is links for tools I use for your consideration: Bar Tool Roll My Jigger (Japanese) My Cocktail Kingdom Shaking Tin Set My Long Bar Spoon My Favorite Flair Bottle My "Flair Shaker" My “US Flag” Cocktail Shaker Tin Cobbler shaker (set) Cocktail Mixing Glass 500ml My Muddler My Ice Scoop Pour spouts we use My Cocktail Kingdom Strainer Amazing Camera I Use For Pictures and Videos

Email to this supplier
  • Mr. Alan.pang
  • Your message must be between 20-8000 characters

Related Productslist

Home

Phone

Skype

Inquiry